To keep the water-borne diseases under control, and keeping oneself safe in extreme cold, one must be careful about utilizing bacteria-free water. For this, geysers are fundamental. Not only they block the attack of microorganisms but also protect us from occasional diseases like cold, fever, and so forth.., Especially, if you are living in Lahore, and have experienced the winters here, you better know these seasonal infections are way too much to handle in harsh winters!

Of course, geysers or water heater systems won’t be utilized during the summer season. Nonetheless, the importance of a geyser cannot be overlooked. Occasional maintenance as well as checks need to be made by hiring the professional geyser service in Lahore to ensure your geyser stays in working condition for an extended period of time.

However, in the article below let us see the basic geyser problems that may occur and how to fix them. For geysers that are electric people may mistake it as a malfunction of the geyser when in reality it’s the electric issue that may be the real problem. This issue needs to be handled by calling up electrician services. Or chances are, if you have got the instant geyser installed, there might be some wirings that have gotten faulty and your electric geyser is not functioning properly. But don’t you worry, electrician services in Lahore are there to save the day!

So let’s discuss common occurring problems associated with geysers and water heater systems!

Water Leakage

There are two types of water leakage problems – Leakage occurring from the top and the second is from the base. The water leakage occurring from the head of the geyser is a very typical issue. If you are suspecting that there is a leakage issue from the top, the first and the foremost thing you ought to do is, switch off the power button, and if it is the geyser, turn the thermostat control to the OFF position. Make sure that the cold-water inlet is not stopped until you discover the leak, as the leak can be stopped without exerting sufficient pressure. Another way to stop the leak would be covering or sealing the pipes and joints.

The water leakage from the base is predominantly because of buildup, a leaking electric heating component gasket, or an incomplete measure of water being let out through the flood pipe on the grounds. This causes the T&P valve to release abundant pressure in the tank. Look up the best geyser service in Lahore for a more professional approach to the problem.

No Heated Water

If the geyser is not producing enough hot water at the necessary temperature, then it is possible that the geyser is not getting power. For the initial step, you should check the electrical switch in the circuit board to ensure that it has not tripped. If by any means it has, switch the breaker off and restart it later on.

If it didn’t trip, turn off the breaker to the water heater’s circuit in the service panel. Eliminate the insulation and the safety corks, being mindful so as not to contact any wires or electrical terminals. Press the red button, the high-temperature cutoff reset button – situated over the upper indoor regulator. Replace the security corks, protection, and access panel. Turn on the geyser’s electrical switch. Electrician service can help you best in this regard.

Water’s excessively hot

If the water is excessively hot than the necessary temperature, turn off the main power to the water heater/geyser in the service panel. Once again, remove the access panel, insulation, and security corks from each warming component on the water heater. Try not to contact any wires or electrical terminals. If you meddle with something that you don’t know, the issue may get bigger. Test the wire to affirm the main power is off, utilizing a voltage analyzer. Set up the heat setting on both the two indoor regulators: They ought to be at a similar temperature. It’s wise to call the electrician services so they can help you in fixing the issue in the best professional way.

Longer than usual time to heat

If the water warming cycle doesn’t occur in the normal required time, then the heater ought to be surveilled for issues. Call out the geyser service in Lahore. In this case, the issue typically lies with the warming components or indoor regulators and those parts could be replaced.

Muddy water result

If the water is corroded, it is because of the consumption in the anode pole or the water tank. For this, you ought to think about replacing the anode bar.

Is it accurate to say that you are encountering the water geyser issues? Stress not! Look up the electrician services for people who have instant geysers installed at their homes or geyser service in Lahore for fool-proof service or repair for the geysers. Recruit an expert from a notable, respectable association for geyser repair. Ensure the expert is authorized and protected. Utilize a professional who will give a forthright clarification of the whole fix measure. Guarantee you have a separate work request that shows precisely what will be done and the amount it will cost – ahead of time!

By laptab